VigorAP 810 v1.2.3 2017-10-27
發表於 : 週二 10月 31日, 2017年 2:11 pm- 1 -
Release Note for VigorAP 810
Firmware Version: 1.2.3
Release Type: Normal
Applied Models: VigorAP 810
With this high cost-efficiency VigorAP 810, computers and wireless devices which are compatible
with 802.11n can connect to existing wired Ethernet network via this VigorAP 810, at the speed of
300Mbps. Easy install procedures allows users to setup a network environment in very short time -
within minutes, even inexperienced users. Just follow the instructions given in this user manual, you
can complete the setup procedure and release the power of this access point all by yourself!
New Features
Support Isolate SSID feature which is useful to decide whether the wireless clients can
access to other clients on different SSIDs if they are in the same subnet.
Add TR-069 parameters related to System Maintenance>>Management.
Improvement
Corrected: WPA2 KRACK vulnerability issue which affected Universal Repeater mode
only. This issue affects all wireless clients so you should check your laptops, phones and
all other wireless clients to see if they need updated software/firmware. Search for
"WPA2 KRACK" with your vendor. See
https://www.draytek.com/en/news/news/20 ... erability/
Improved: Support data compression / decompression for AP management.
Improved: Add TR-069 parameters related to Detection, Policy and Statistics for Mobile
Device Management.
Corrected: System administrator modified the HTTPS port number for VigorAP 810 from
VigorACS. As a result, VigorACS lost the control and could not access into VigorAP
again after rebooting VigorAP.
Corrected: A space appeared after the parameter value of TotalSendByte /
TotalReceiveByte that Vigor CPE replied to VigorACS.
Corrected: Minimum RSSI Roaming did not work.
Corrected: The USB temperature sensor “RDing TEMPer2V1.3” did not work properly
on VigorAP 810.
- 2 -
Known Issue
None.
Notes
None
RD NO: 106_10_20
Release Note for VigorAP 810
Firmware Version: 1.2.3
Release Type: Normal
Applied Models: VigorAP 810
With this high cost-efficiency VigorAP 810, computers and wireless devices which are compatible
with 802.11n can connect to existing wired Ethernet network via this VigorAP 810, at the speed of
300Mbps. Easy install procedures allows users to setup a network environment in very short time -
within minutes, even inexperienced users. Just follow the instructions given in this user manual, you
can complete the setup procedure and release the power of this access point all by yourself!
New Features
Support Isolate SSID feature which is useful to decide whether the wireless clients can
access to other clients on different SSIDs if they are in the same subnet.
Add TR-069 parameters related to System Maintenance>>Management.
Improvement
Corrected: WPA2 KRACK vulnerability issue which affected Universal Repeater mode
only. This issue affects all wireless clients so you should check your laptops, phones and
all other wireless clients to see if they need updated software/firmware. Search for
"WPA2 KRACK" with your vendor. See
https://www.draytek.com/en/news/news/20 ... erability/
Improved: Support data compression / decompression for AP management.
Improved: Add TR-069 parameters related to Detection, Policy and Statistics for Mobile
Device Management.
Corrected: System administrator modified the HTTPS port number for VigorAP 810 from
VigorACS. As a result, VigorACS lost the control and could not access into VigorAP
again after rebooting VigorAP.
Corrected: A space appeared after the parameter value of TotalSendByte /
TotalReceiveByte that Vigor CPE replied to VigorACS.
Corrected: Minimum RSSI Roaming did not work.
Corrected: The USB temperature sensor “RDing TEMPer2V1.3” did not work properly
on VigorAP 810.
- 2 -
Known Issue
None.
Notes
None
RD NO: 106_10_20