VigorAP800 v1.1.6 Release

版主: david

VigorAP800 v1.1.6 Release

文章門神 » 週二 10月 4日, 2016年 1:08 pm

Release Note for VigorAP 800
Firmware Version: 1.1.6
Release Date: August 22, 2016
Applied Models:
VigorAP 800
"With this high cost-efficiency VigorAP 800, comput
ers and wireless devices which are compatible
with 802.11n can connect to the existing Ethern
et network via this VigorAP800. 300Mbps wireless
transmission rates is ideal for bandwidth-heavy task
s. Easy install procedur
es allow any computer
users to setup a network environment in very
short time - within minutes, even inexperienced
users."
New Features

Support HTTPS for web user interface.
Improvement

Improved: Display the correct
channel setting for Universal
Repeater Mode chosen in
WLAN 2.4G and WLAN 5G in
System Maintenance>>System Status
.

Improved: Offer a warning message to ask th
e user changing default admin password.

Improved: A warning message with the me
ssage of HTTP/HTTPS port number changed
appears before AP reboots.

Improved: Display Device Name on the main screen.

Corrected: Duplicate IP addre
sses for gateway displayed in
Online Status
under
Universal Repeater mode for WLAN 2.4G.

Corrected: SSID was displayed in
System Maintenance>>System Status
when AP
Bridge-Point to Point was selected for WLAN 2.4G.

Corrected: VigorAP sent a parameter,
“InternetGatewayDevice.ManagementServe
r.UDPConnectionRequestAddress”, with
empty values which caused wrong IP address captured by VigorACS.

Corrected: Management VLAN was not wo
rking well when AP Management was
enabled.

Corrected: Wireless LAN 2.4G had been disabled, however SSID was still be searched.

Corrected: Gateway configured with static
IP in Universal Repeater Mode would be
missing.
- 2 -

Corrected: Internet access via Wi-Fi failed after enabling VLAN Tag Priority.

Corrected: Could not use “,” for pass phras
e (warning message of invalid characters
displayed) in Wireless LAN >> Universal Repeater.

Corrected: Wrong ARP information responded
under Repeater Mode of WLAN 5G.

Improved: The TX/RX Rate value displayed
in Wireless LAN 2.4G > Station List was
offset to the left:

Corrected: No Internet access via Wi-Fi af
ter checking Enable Management VLAN:

Corrected: When Station-Infrastructure m
ode was selected and Enable WLAN 2.4G
function was enabled, an error occurred.

Corrected: When Station-Infrastructure mode
was selected and the pr
ofiles were set in
Wireless LAN>>General Setup
, a configuratio
n error occurred.

Corrected: Unable to define CPE Username and Password for TR-069.

Improved: Color change for the word of “Note” in
Wireless LAN>>General Setup
.

Corrected: Daylight Saving Time of M
ountain Time Zone was incorrect.

Corrected: Internet access via Wi-Fi failed when
Static IP type is selected in Universal
Repeater mode.

Corrected: Airplay did not work
over Universal Repeater link.

Corrected: VigorAP queried DNS for “pool.nt
p.org” every 10 seconds when staying at
Time and Date page.

Corrected: LAN-A IP address could not be c
onfigured and could not be shown in Online
Status while under Universal Repeater mode.

Corrected: WLAN 5G Bandwidth Ma
nagement did not work well.

Corrected: After finished bandwidth manage
ment (for SSID 3 and SSID 4) for wireless
station and clicked OK, a pop up dialog woul
d appear and display warning message.
Known Issue

None
Notes

None
ps:求助順序請直接
(1)電洽 04-2260-5121 / 0963-685-121
(2)http://line.naver.jp/ti/p/%40xat.0000132120.jmw 技術客服 LINE
(3)問題請優先洽詢 help@ublink.org
Telegram 頻道 Channel https://t.me/ublinkorg 韌體更新發佈
其他線上聯絡方式,http://www.ublink.org/index.php/contact
頭像
門神
 
文章: 6265
註冊時間: 週五 12月 8日, 2006年 11:10 am
來自: 台中
送出感謝: 16
擁有感謝: 0 次

回到 Draytek 軔體更新討論區

誰在線上

正在瀏覽這個版面的使用者:Google [Bot] 和 20 位訪客

cron