VigorAP900 v1.1.6 Release note

版主: david

VigorAP900 v1.1.6 Release note

文章門神 » 週一 9月 28日, 2015年 9:02 am

- 1 -
Release Note for VigorAP 900
Firmware Version: 1.1.6
Release Date: August 26, 2015
Applied Models:
VigorAP 900
VigorAP 900, the concurrent dual band wireless (2.4G/5G) access point, offers high-speed data
transmission. With this high cost-efficiency VigorAP 900, computers and wireless devices which
are compatible with 802.11n/802.11a can connect to existing wired Ethernet network via this
VigorAP 900, at the speed of 300Mbps. Easy install procedure allows users to setup a network
environment in very short time - within minutes, even inexperienced users. Also, VigorAP900 is a
Power over Ethernet Powered Device which adopts the technology of PoE for offering power
supply and transmitting data through the Ethernet cable.
New Features
Add Event log for AP Management.
Add Dashboard for AP Management.
Add Diagnostics >> Traffic Graph.
Add Central AP Management >> Access Control.
Add Central AP Management >> Settings.
Support Band Steering.
Support AP Management related parameters based on TR-069 for VigorACS.
Improvement
Improved: Add event log for AP management.
Improved: Add a button named “Analysis” in the page of Diagnostics >> Station
Statistics.
Corrected: Apple cell phone could not connect to VigorAP with WLAN 5GHz.
Corrected: The default gateway IP address could not be displayed normally under
Universal Repeater Mode with static IP.
Corrected: Traffic error occurred when Idle Time was set for Force Overload
Disassociation in the page of Central AP Management>>Load Balance.
Corrected: After disabling the wireless function of VigorAP, the connected device would
then disconnect and disappear on the Access Station List page.
- 2 -
Corrected: Each index entry can be set with the same settings for WDS configuration.
Corrected: Wrong tip window was displayed when WEP/802.1x was selected as Mode
setting in Quick Start Wizard>>Wireless Security (5GHz).
Corrected: Related fields for Universal Repeater (2.4G) were still displayed on System
Maintenance>> System Status page when 2.4G wireless function for Universal Repeater
was disabled.
Corrected: General information such as SSID, Encryption and Version of VigorAP could
not be shown correctly in Central AP Management>>Status.
Corrected: When Channel was configured with “Auto channel”, only Channel 1 could be
detected and selected.
Corrected: Display error of RSSI configuration in Station List.
Corrected: Functions of airtime fairness, session control, band steering, roaming appeared
when AP Bridge-Point to Point/AP Bridge-Point to Multi-Point mode for Wireless LAN
2.4G connection.
Corrected: Wrong data display (channel, Tx/Rx packets) for VigorAP in the page of
Online Status when Universal Repeater mode was selected for Wireless LAN 2.4G/5G.
connection.
Corrected: Wrong date and time display in Traffic Graph.
Corrected: No data would be displayed in the page of Diagnostics >> Station Statistics
>> Passing Number.
Corrected: The Diagnostics >> Station Statistics page could not display correct statistics
chart.
Corrected: Wireless LAN 2.4G Station Control SSID2~4 did not work.
Improved: Add format check for RADIUS profile.
Improved: Modify the web page of Configuration Backup and file name filtering
mechanism for Restoration.
Improved: Wireless LAN 5G DFS Channel display error.
Known Issue
None
Notes
Modifications
None
ps:求助順序請直接
(1)電洽 04-2260-5121 / 0963-685-121
(2)http://line.naver.jp/ti/p/%40xat.0000132120.jmw 技術客服 LINE
(3)問題請優先洽詢 help@ublink.org
Telegram 頻道 Channel https://t.me/ublinkorg 韌體更新發佈
其他線上聯絡方式,http://www.ublink.org/index.php/contact
頭像
門神
 
文章: 6265
註冊時間: 週五 12月 8日, 2006年 11:10 am
來自: 台中
送出感謝: 16
擁有感謝: 0 次

回到 Draytek 軔體更新討論區

誰在線上

正在瀏覽這個版面的使用者:沒有註冊會員 和 18 位訪客

cron